The Nissan DataScan II for Windows is intended for newer Nissan cars equipped with gray 16 pin OBDII connecter and use Consult II protocol over K line (DDL2) up to year 2007. The connector is usually located near the fuse box.A list of cars that the software has been tested on is located on the page. The list is by no means comprehensive and is constantly being updated as new vehicles are tested.NOTE: NOT COMPATIBLE with 2008+ cars that use the CAN BUS protocol.
Some vehicles up to year 2004 use OBDII (K-Line) for communicating with the ECU, BUT still use the Consult I (14pin) port for diagnostics.The software can be used with our FTDI FT232RL based. The ELM327 chip based adapters are NOT compatible.Compatible OS: Windows XP 7 8 8.1 10 (32/64bit)The Nissan DataScan II software supports factory Nissan ECUs. Aftermarket ECUs like Apexi Power FC or F-Con V Pro are not compatible with the software.The latest software release supports diagnostics of following control modules: ECM, BCM, TCM, ABS, SRS and ECMD (ECM Diesel) over the K line (DDL2). Note: Some vehicles may use K line for diagnostics of engine ECU (ECM) but still use DDL1 line for diagnostics of other control modules. This software does not support diagnostics over the DDL1 line. ECU Part NumberThis is the main window of the NDSII software which shows the ECM Nissan Identification part number.
Basic and Advance Functions can be selected by clicking on the buttons, using the shortcut keys (F1 - F11) or using the Menu bar. Most functions except Data Replay and Log Analyser are disabled until communication with the ECU is successfully established.Progress bar at the bottom indicates communication between the ECU and PC. If the bar is not moving there is no data being received from the ECU. Active Test ECMActive Test allows users to temporary modify some of the engine parameters for testing purposes. They return to their original values when a function is stopped, PC disconnected or engine restarted.Note: It is possible to damage the engine if the A/F Base% functions is used to excessively modify fuel delivery. Likewise the engine may overheat if the Engine Temperature is set to low for a long period of time. Do not use those functions if you are not sure how they will effect your engine.Below is a video of Active Test function in use.
Work SupportWork Support functions allow users to perform some of the advance service procedures. Those procedures may need to be performed after replacement parts are installed.Clear Self Learn - clears the A/F Base SL map learned by the ECU.Idle Air Volume Learn - is an operation to learn the fully closed position of the throttle valve.Program Immobiliser Key - allows to register the Nissan transponder keys with the Immobiliser Note: The immobiliser security PIN CODE needs to be known.
Initially all registered keys will be erased and all keys will need to be reregistered. ECU Part Number BCMThe BCM tab shows the BCM Nissan Identification part number. Basic Functions can be selected by clicking on the buttons or using the Menu bar. All functions are disabled until communication with the ECU is successfully established.Progress bar at the bottom indicates data being send between the ECU and PC. If the bar is not moving there is no data being received from the ECU.Note: Some vehicles may use K line for diagnostics of engine ECU (ECM) but still use DDL1 line for diagnostics of other control modules.
This software does not support diagnostics over the DDL1 line. Some of those models are: X-trail, Maxima, Patrol. ECU Part Number TCMThe TCM tab shows the TCM Nissan Identification part number. Basic Functions can be selected by clicking on the buttons or using the Menu bar. Most functions except Data Replay and Log Analyser are disabled until communication with the ECU is successfully established.Progress bar at the bottom indicates data being send between the ECU and PC.
If the bar is not moving there is no data being received from the ECU.Note: Some vehicles may use K line for diagnostics of engine ECU (ECM) but still use DDL1 line for diagnostics of other control modules. This software does not support diagnostics over the DDL1 line.
Some of those models are: X-trail, Maxima, Patrol. ECU Part Number ABSThe ABS tab shows the ABS Nissan Identification part number. Basic Functions can be selected by clicking on the buttons or using the Menu bar. Most functions except Data Replay and Log Analyser are disabled until communication with the ECU is successfully established.Progress bar at the bottom indicates data being send between the ECU and PC. If the bar is not moving there is no data being received from the ECU.Note: Some vehicles may use K line for diagnostics of engine ECU (ECM) but still use DDL1 line for diagnostics of other control modules. This software does not support diagnostics over the DDL1 line. Some of those models are: X-trail, Maxima, Patrol.
ECU Part Number SRSThe SRS tab shows the SRS Nissan Identification part number. Basic Functions can be selected by clicking on the buttons or using the Menu bar. All functions are disabled until communication with the ECU is successfully established.Progress bar at the bottom indicates data being send between the ECU and PC. If the bar is not moving there is no data being received from the ECU.Note: Some vehicles may use K line for diagnostics of engine ECU (ECM) but still use DDL1 line for diagnostics of other control modules. This software does not support diagnostics over the DDL1 line.
Nissan Datascan Ii Crack
Some of those models are: X-trail, Maxima, Patrol. Work SupportWork Support functions allow users to perform the advance service procedures. Those procedures may need to be performed after replacement parts are installed.Program Immobiliser Key - allows to register the Nissan transponder keys with the Immobiliser Note: The immobiliser security PIN CODE needs to be known.